Film Roll Clamp Cart & Roll Handling Equipment

Send roll specs. Get a practical sizing plan.

A fast recommendation starts with the load and workplace: material type, weight, diameter, width, lift height, rotation need, aisle width and site photos.

Material type: film, paper, tape jumbo roll or other cylindrical load

Single roll weight and whether the roll core is rigid enough for clamping

Outside diameter range and roll width / height

Pickup direction: vertical clamp, horizontal clamp or both

Lift height at clamp center and machine-side loading height

Aisle width, turning space and 10-20 cm side clearance

Battery preference: 12V/80Ah, 24V, 24V/220Ah or custom

Use frequency: daily roll moves, transfer distance and whether stand-on drive is needed

Document needs: MSDS/SDS, transport identification, non-dangerous booking or export files

Site photos: roll storage, machine inlet, floor and route

A fast recommendation starts with the load and workplace: material type, weight, diameter, width, lift height, rotation need, aisle width and site photos.

Name / Company Email / WhatsApp

Material Single roll weight

Outside diameter Roll width / height

Lift height Rotation need

Recommended configuration

Share roll weight, diameter and rotation need to get a practical starting configuration.

Sizing assistant

Application scene Other site notes

By submitting, you agree that Dubhe may use these parameters, contact details and site context to prepare a roll handling recommendation and respond to your inquiry.

WhatsApp Email

Practical product parameters and custom range

These custom roll clamp configurations are not fixed catalogue models. The ranges give buyers a practical starting point before final sizing.

Parameters can be customized by roll weight, diameter, width, lift height, aisle width, floor condition, battery requirement and whether the roll is picked vertically or horizontally. Keep 10-20 cm clearance on both sides of the clamp during operation.

Higher lift / heavy daily use

Counterbalanced electric roll clamp

For production lines that need electric travel, electric lifting and hydraulic clamping with a higher mast.

Rated load: 500 kg
Lift height: 3000 mm clamp-center height
Roll diameter: 300-800 mm
Rotation: 360 degrees, left/right
Battery: 24V 220Ah lead-acid
Aisle: about 1400 mm
Truck size: about 1020 mm wide, 1850 mm high; 1600/2100 mm mast optional
Drive / lift motor: 1.2 kW / 2.2 kW

Suitable for rigid film rolls, paper rolls and hard-core roll material
Counterbalanced layout, no front support legs under the roll
Wear-resistant rubber pads on clamp plates

Best fit

High lift point or machine-side loading above standard height
Frequent daily use with powered travel and lift
Roll underside must stay clear of front support legs

Avoid when

Very narrow aisles below the confirmed turning radius
Soft or easily deformed rolls that cannot tolerate side pressure

Confirm first

Actual roll weight and hardness
Clamp-center height and machine inlet height
Aisle width, turning space and floor condition

Standard film roll loading

Stand-on electric rotating clamp

A compact electric travel model for vertical pickup and repeated machine-side roll feeding.

Rated load: 500 kg
Lift height: 1500 mm
Roll diameter: 360-800 mm
Roll height: 1320 mm reference
Rotation: 360 degrees, dual hydraulic
Voltage: 24V
Pump power: 24V / 1600 W
Aisle: about 1100 mm
Reference size: 1.8 x 0.8 x 1.6 m

Good fit for slitter, rewinder and packaging line loading
Electric travel with stand-on operation
Used when rolls are picked upright and rotated into position

Best fit

Repeated loading beside slitters, rewinders and packaging lines
Vertical pickup followed by 360 degree positioning
Medium travel distance where stand-on driving improves rhythm

Avoid when

Loads needing more lift height than the 1500 mm reference
Rolls outside the confirmed clamp diameter range

Confirm first

Roll diameter, roll height and core strength
Whether left/right rotation is required
Clearance around the machine-side loading point

Lower frequency / budget option

Semi-electric manual-push clamp

For short indoor transfers where electric lifting and clamping are needed, but travel can remain manual.

Rated load: 350 kg
Lift height: 1500 mm
Roll diameter: 360-800 mm
Roll height: 1600 mm reference
Rotation: 360 degrees, dual hydraulic
Battery: 12V / 80Ah
Pump power: 12V / 1600 W
Aisle: about 1100 mm
Reference size: 1.3 x 0.95 x 1.9 m
Light film-roll option: 250 kg, 1500 mm lift, 600-800 mm roll diameter
Battery option: 12V / 80Ah or 12V / 120Ah by duty cycle

Best for short-distance transfer and fewer daily cycles
White nylon or polyurethane wheels for epoxy and painted floors
Lower purchase cost while keeping electric lift and clamp actions
A lighter 250 kg film-roll version can be considered for low-frequency loading.

Best fit

Short indoor transfer with low or medium frequency
Budget-sensitive sites that still need powered lift and clamp rotation
Smooth floors where manual pushing is acceptable

Avoid when

Long travel routes or high daily cycle counts
Steep slopes, rough floors or heavy continuous duty

Confirm first

Daily handling count and travel distance
Operator pushing route and turning points
Battery endurance and wheel material for the floor

Side pick / large diameter

Side-clamp paper roll and cable roll cart

For cloth rolls, paper rolls, cable reels and other cylindrical loads that are handled from the side instead of full 360 degree rotation.

Reference load: 500-800 kg
Applicable diameter: 200-1300 mm
Tilt angle: Left / right 30 degree reference
Lift / drive: Electric lift, electric travel option
Fork / clamp: Thickened fork frame with side clamp
Custom confirmation: Roll hardness, core strength and side clearance

Useful when the roll cannot be gripped from the bottom or rotated fully
Suitable for cloth, paper, cable and other large-diameter cylindrical loads
Parameter range must be checked against roll weight, width and center of gravity

Fit

Side-pick loading where a roll sits on a pallet or machine cradle
Large roll diameter beyond ordinary small clamp range
Paper, cloth or cable reels that require gentle side holding

Avoid

Thin film rolls that need precise 360 degree machine-side rotation
Very soft rolls that cannot accept side pressure

Confirm

Actual roll diameter and width
Allowed side pressure and core strength
Need for 30 degree tilt or full 360 degree rotation

Documentation and shipment support

The website should describe document types that can be prepared for real orders. Final files depend on the actual truck, battery, route and carrier requirement.

Battery MSDS/SDS

Lead-acid battery configurations can be supported with safety documents covering valve-regulated, maintenance-free and non-spillable descriptions.

Transport identification

Transport attribute or identification documents can be prepared according to actual model, battery, packaging and route.

Non-dangerous booking support

Non-dangerous booking documents can be prepared according to carrier and destination requirements for material-handling equipment shipments.

Custom confirmation files

Final documents should match load, roll diameter, roll width, lift height, voltage, battery and packaging instead of treating reference ranges as fixed models.

Roll handling equipment FAQ

Short answers for buyers comparing roll clamp carts, forklifts, lifters and machine-side loading equipment.

What is a roll clamp material handling cart?

It is a compact material handling vehicle that clamps the outside diameter of a round load, lifts it and can rotate or transfer it to the next workstation.

Can it load film rolls into slitters and rewinders?

Yes. The key use case is taking film rolls, paper rolls or tape jumbo rolls from floor or pallet height and positioning them near slitting, rewinding, coating or packaging equipment.

Is this a standard forklift?

No. A standard forklift is optimized for pallets. A roll clamp cart holds the roll circumference and controls round, rolling material.

What parameters are needed for sizing?

Roll type, weight, outside diameter, width, required lift height, rotation requirement, aisle width, floor condition and machine-side photos are enough for an initial recommendation.

Are the parameters fixed catalogue values?

No. Load, mast height, clamp diameter, roll width, battery, wheel material and counterweight layout can be customized after checking the actual roll and site.

Can you support battery MSDS/SDS documents?

Yes. For lead-acid battery configurations, matching MSDS/SDS documents can be prepared according to the actual battery model and shipment requirement.

Can transport or non-dangerous cargo documents be prepared?

Supporting transport identification and non-dangerous booking documents can be prepared according to the actual configuration, route and carrier requirement.